Receiver:Details | Type:C40E-S146 | Part no.:1081932
Sender:Details | Type:C40S-S146 | Part no.:1081931
Videos
Quality assurance of light beam systems
Tutorial Safety light beam basics (1/8): What is the purpose of safety light beams?
Features
| Application | Explosive areas |
| Ex-approvals |
ATEX for gas: II 3G Ex nA op is IIC T4 Gc X ATEX for dust: II 3D Ex tc IIIC T135°C Dc |
| System part | Pair |
| Resolution | 20 mm |
| Protective field height | 900 mm |
| Scanning range | 21 m |
| Synchronization | Optical synchronisation |
| Integrated laser alignment aid | ✔ |
Safety-related parameters
| Type | Type 4 (IEC 61496-1) |
| Safety integrity level | SIL3 (IEC 61508) |
| Category | Category 4 (EN ISO 13849) |
| Performance level | PL e (EN ISO 13849) |
| PFHD (mean probability of a dangerous failure per hour) | 15 x 10-9 (EN ISO 13849) |
| TM (mission time) | 20 years (EN ISO 13849) |
| Safe state in the event of a fault | At least one OSSD is in the OFF state. |
Functions
| Functions | Delivery status | |
|---|---|---|
| Protective operation | ✔ | |
| Restart interlock | ✔ | Internal |
| External device monitoring (EDM) | ✔ | Deactivated |
| Beam coding | ✔ | Code 1 |
| Configurable scanning range | ✔ | |
| Reduced resolution | ✔ | Deactivated |
| Fixed blanking | ✔ | Deactivated |
| Floating blanking | ✔ | Deactivated |
| Dynamic blanking for object pattern recognition | ✔ | |
| Self-teaching dynamic blanking for goods detection | ✔ | |
| Self-teaching dynamic blanking for pallet detection | ✔ | |
| Multiple sampling | ✔ | 2x evaluation |
| Direction monitoring | ✔ | |
| Virtual photoelectric switches | ✔ | |
| Sensor gap monitoring | ✔ | |
| Sequence monitoring | ✔ | |
| Object entry monitoring | ✔ | |
| Detection of geometrically even objects | ✔ | |
| Safe SICK device communication via EFI | ✔ | |
Functions in combination with UE402
| Bypass | ✔ |
| Operating mode switching | ✔ |
Interfaces
|
|||||||||
| Configuration connection | Female connector M8, 4-pin | ||||||||
| Configuration method | PC with CDS (Configuration and Diagnostic Software) | ||||||||
| Display elements | 7-segment display | ||||||||
1) Depending on load, power supply and wire cross-section. The technical specifications must be observed.
Electrical data
| Protection class | III (IEC 61140) | ||||||||||
| Supply voltage VS | 24 V DC (19.2 V ... 28.8 V) 1) | ||||||||||
| Residual ripple | ≤ 10 % 2) | ||||||||||
|
|||||||||||
| Application diagnostic output (ADO) | |
| Type of output | PNP semiconductor, short-circuit protected 3) |
| Output voltage HIGH (active) | 24 V DC (VS – 4.2 V DC ... VS) |
| Output voltage LOW (deactivated) | High resistance |
| Output current HIGH (active) | ≤ 100 mA |
1) The external voltage supply must be capable of buffering brief mains voltage failures of 20 ms as specified in EN 60204-1. Suitable power supplies are available as accessories from SICK.
2) Within the limits of VS.
3) Applies to the voltage range between –30 V and +30 V.
Mechanical data
| Dimensions | See dimensional drawing |
| Housing cross-section | 48 mm x 40 mm |
| Housing material | Aluminum extruded profile |
Ambient data
| Enclosure rating | IP65 (EN 60529) |
| Ambient operating temperature | 0 °C ... +55 °C |
| Storage temperature | –25 °C ... +70 °C |
| Air humidity | 15 % ... 95 %, Non-condensing |
| Vibration resistance | 5 g, 10 Hz ... 55 Hz (EN 60068-2-6) |
| Shock resistance | 10 g, 16 ms (EN 60068-2-27) |
Other information
| Wave length | 950 nm | ||||||||
| Type of light | Near-infrared (NIR), invisible | ||||||||
|
|||||||||
